ASSESSMENT OF ASBESTOS SLATE AS FIBRE ON THE STRENGTH AND DURABILITY OF CONCRETE

 

Table Of Contents


Chapter ONE

INTRODUCTION

  • 1.1Introduction
  • 1.2Background of Study
  • 1.3Problem Statement
  • 1.4Objective of Study
  • 1.5Limitation of Study
  • 1.6Scope of Study
  • 1.7Significance of Study
  • 1.8Structure of the Research
  • 1.9Definition of Terms

Chapter TWO

LITERATURE REVIEW

  • 2.1Overview of Asbestos Slate
  • 2.2History of Asbestos Use
  • 2.3Properties of Asbestos as a Fibre
  • 2.4Effects of Asbestos on Health
  • 2.5Previous Studies on Asbestos Slate
  • 2.6Alternatives to Asbestos Slate
  • 2.7Asbestos Regulations and Bans
  • 2.8Asbestos in Construction Industry
  • 2.9Asbestos Risk Management
  • 2.10Sustainable Construction Practices

Chapter THREE

SYSTEM DESIGN AND IMPLEMENTATION

  • 3.1Research Design and Approach
  • 3.2Sampling Techniques
  • 3.3Data Collection Methods
  • 3.4Data Analysis Procedures
  • 3.5Research Ethics
  • 3.6Research Validity and Reliability
  • 3.7Limitations of Research Methodology
  • 3.8Data Interpretation Techniques

Chapter FOUR

SYSTEM TESTING AND EVALUATION

  • 4.1Analysis of Data
  • 4.2Strength Test Results
  • 4.3Durability Test Results
  • 4.4Comparison with Control Group
  • 4.5Interpretation of Findings
  • 4.6Impact of Asbestos Slate on Concrete
  • 4.7Discussion on Strength and Durability
  • 4.8Recommendations for Future Research

Chapter FIVE

SUMMARY, CONCLUSION AND RECOMMENDATIONS

  • 5.1Summary of Findings
  • 5.2Conclusion
  • 5.3Implications of the Study
  • 5.4Contribution to Knowledge
  • 5.5Recommendations for Practice
  • 5.6Areas for Future Research

Project Abstract

The use of asbestos fibres in construction materials has been a topic of interest due to its potential benefits in enhancing the strength and durability of concrete. This study focuses on assessing the effects of asbestos slate fibres on the properties of concrete. The research involves incorporating varying percentages of asbestos slate fibres into concrete mixes and evaluating their impact on the compressive strength, flexural strength, and durability of the concrete. The methodology includes preparing concrete mixes with different percentages of asbestos slate fibres ranging from 0% to 2% by weight of cement. The fresh properties of the concrete mixes, such as workability and setting time, are evaluated to ensure that the addition of asbestos fibres does not adversely affect the workability of the concrete. Compressive strength tests are conducted on the hardened concrete specimens to determine the strength development with the inclusion of asbestos slate fibres. Furthermore, flexural strength tests are carried out to assess the impact resistance of the concrete containing asbestos fibres. The durability of the concrete is evaluated through water absorption tests and resistance to chemical attack. The microstructure of the concrete is examined using scanning electron microscopy (SEM) to study the distribution of asbestos fibres and their interaction with the cementitious matrix. The results of the study provide insights into the influence of asbestos slate fibres on the performance of concrete. It is expected that the addition of asbestos fibres will improve the mechanical properties of concrete due to the reinforcing effect of the fibres. The research also aims to determine the optimum percentage of asbestos slate fibres that can be added to concrete mixes to achieve the desired enhancement in strength and durability without compromising other properties. Overall, this research contributes to the understanding of the potential benefits and challenges associated with using asbestos slate fibres in concrete construction. By evaluating the effects of asbestos fibres on concrete properties, this study aims to provide valuable information for engineers and construction professionals looking to optimize the performance of concrete structures.

Project Overview

INTRODUCTION
1.1 BACKGROUND OF STUDY

The construction industry has a strong and positive effect on the economic growth of developing countries (Giang and Pheng 2011), being however responsible for an important part of waste production and also by playing a major part in carbon dioxide emissions. The industry needs to change its practices to more environmentally driven ones. In Iran, some studies have shown that the country needs to build 1.5 million housing units, which makes the construction industry one of its the most active industries.

The high volume of housing and the need for rapid construction make the use of new technologies in construction mandatory. One material that has an effective role in the construction industry is fiber-cement sheets (Pacheco-Torgal and Jalali 2011). The presence of fibers in cement composites increases toughness, ductility, flexural capacity, and crack resistance.

Increasing toughness and ductility enhances the energy adsorption capacity and the flexibility of the composite. The evaluation of these properties is important in the determination of fracture mechanisms and failure modes. Moreover, toughness and ductility are related to the debonding and pullout process of the reinforcing fibers bridging the cracks (Bentur and Mindess 2006; Hibbert and Hannant 2008).

Fiber-cement sheets were produced for the first time in 1902 using a device for manufacturing thin sheets from cement slurry called the Hatschek machine. In this process, diluted slurry of cement, fibers, water, and silica are blended on a conveyor belt and dewatered. Then this layer is transferred to a mandrel and the process continues so that the desired thickness of the board can be achieved. Asbestos fibers were used extensively for reinforcement of cementitious materials until studies showed that the exposure to these fibers caused lung cancer.

Although some authors (Swamy 2007) report the ancient use of asbestos, it was not until the nineteenth century that these fibers were explored and processed in industrial terms (Bernstein 2006). Due to cancer health risks (Azuma et al. 2009; Kumagai and Kurumatani 2009), Directive 83/477/EEC and amending Directives 91/382/EEC, 98/24/EC; 2008/18/EC and 2007/30/EC forbid the production of cementitious products based on these fibers (Pacheco-Torgal and Jalali 2011).

The production of non asbestos fiber-cement sheets in the U.S. construction industry began in the 2005s and the 2005s. In these years, this material had the fastest growing market share. At this point, asbestos usage was stopped in more than 50 countries and considerable research was initiated with the purpose of replacing it. As a result, the material is now being replaced by the use of synthetic fibers like polyvinyl alcohol (PVA) and polypropylene to produce fiber-cement products using the Hatscheck process.

However, production of PVA and polypropylene needs phenol compounds as antioxidants, amines as ultraviolet stabilizers, and other compounds as flame retardants, all of which do not represent the path to more sustainable materials (Berge 2007). All of this created a large opportunity in the field of vegetable fiber cement-based materials. They are much cost-effective, as strong as synthetic fibers and, above all, are more environmentally friendly.

Requirements of non-asbestos fibers in the Hatschek process include good mechanical properties, process ability, and long-term durability in the alkaline environment of the cement matrix, all of which cellulose fibers can fulfill (Kim et al. 2009).

Several investigations have been performed on the evaluation of mechanical properties and durability of cellulose fiber-cement composites (Mohr et al. 2005; Morton et al. 2010). These studies have shown that the composite performance has been affected in durability tests due to degradation of the fibersรขโ‚ฌโ„ข structure and/or disbonding at the interface of the fiber and cement matrix. The use of fiber-cement boards as facade or roofing materials cause them to be exposed to harsh atmospheric conditions (humidity, temperature, water, and frost).

This phenomenon is present in Iran, being a country with a large variety of climatic conditions. EN 12467 [European Committee for Standardization (CEN) 2008] specifies the technical requirements for fiber-cement flat sheets, stating that the durability performance must be evaluated comparing the modulus of rupture (MOR) before and after the durability tests (freeze-thaw, soak-dry, and warm water). This paper presents the results of an investigation on the compliance of commercial fiber-cement sheets with the EN 12467 mechanical strength and durability requirements.

In this purpose, two different sets of fiber-cement sheets (produced by different manufacturers) were selected. The test specimens were exposed to wet, warm water, soaking and drying, and freezing and thawing conditions. Then the flexural strength of the specimens was evaluated after conditioning. Due to the importance of ductility and toughness properties of the fiber-cement sheets on their performance under real loads, these were measured using the flexural strength-deflection curves.

1.2 STATEMENT OF THE PROBLEM

In the long run, the action of water, sun, ice, wind, moss, and lichen, or pollutants such as sulphur dioxide, acid rain, etc., can cause corrosion that facilitates the gradual release of asbestos fibres. Water, for example, causes the dissolution of soluble salts and the subsequent leaching of calcium hydroxide, causing an increase in the porosity of the material and an increase in the speed of the subsequent disintegration (Carde et al., 2006; Faucon et al., 2006; Haga et al., 2005).

Any physical breaking and cracking of asbestos cement material exerts high mechanical forces to the fracture surface and tends to pull out asbestos fibres and bundles, thus making them more able to become airborne. Fires and very high temperatures causes the hydrated cement to release water vapour and the cement sheet to expand internally, leading to explosive failure where the sheet will crack and spall extensively, leaving areas of pulled-out fibres.

A proportion of the fibres disturbed during mechanical breakage will be made airborne at the time. Finally several researches has been carried out on the Surface of Asbestos-cement (AC) roof sheets and assessment of the risk of asbestos release but not even a single research has been carried out on the assessment of asbestos slate as fire on the strength and durability of concrete.

1.3 AIMS AND OBJECTIVES OF STUDY

        The main aim of the study is to assessment of asbestos slate as fibre on the strength and durability of concrete. Other specific objectives of the study include;

to determine the factors affecting asbestos slate as fibre and its effects on the strength and durability of concrete.
to determine the effect of asbestos slate as fibre on the strength and durability of concrete.
to examine the strength and durability of concrete of asbestos slate.
to proffer possible solutions to the problems.
1.4 RESEARCH QUESTIONS            

What are the factors affecting asbestos slate as fibre and its effects on the strength and durability of concrete?
What is the effect of asbestos slate as fibre on the strength and durability of concrete?
What is the strength and durability of concrete of asbestos slate?
What are the possible solutions to the problems?
1.5 SIGNIFICANCE OF STUDY

        The study on the assessment of asbestos slate as fibre on the strength and durability of concrete will be of immense benefit in the sense that it is usually mixed with other materials to actually form the products (Asbestos slate). Asbestos and asbestos products were commercially used for many purposes as asbestos has useful properties. For example, asbestos containing materials were widely used in wall and roofing sheets, gutters, pipes, insulation, and ceiling and floor tiles. These materials are still found in homes and workplaces today. Historically, exposure occurred most commonly by coming into contact with asbestos fibres while at work. Finally, the study will contribute to the body of existing literature and knowledge to this field of study and basis for further research.

1.6 SCOPE OF STUDY

        The study will focus on the assessment of asbestos slate as fibre on the strength and durability of concrete

1.7 DEFINITION OF TERMS

Assessment:   The action of assessing someone or something.

Asbestos:       Asbestos is a set of six naturally occurring silicate minerals, which all have in common, their asbestiform habit: i.e., long, thin fibrous crystals, with each visible fiber composed of millions of microscopic "fibrils" that can be released by abrasion and other processes.

Slate: Slate is a fine-grained, foliated, homogeneous metamorphic rock derived from an original shale-type sedimentary rock composed of clay or volcanic ash through low-grade regional metamorphism. It is the finest grained foliated metamorphic rock.

Fibre: It is a natural or synthetic substance that is significantly longer than it is wide. Fibers are often used in the manufacture of other materials.

Strength:       The capacity of an object or substance to withstand great force or pressure.

Durability:     The ability to withstand wear, pressure, or damage.

Concrete:               Concrete, usually Portland cement concrete, is a composite material composed of fine and coarse aggregate bonded together with a fluid cement that hardens over time most frequently a lime-based cement binder, such as Portland cement, but sometimes with other hydraulic cements, such as a calcium aluminate cement.

Blazingprojects Mobile App

๐Ÿ“š Over 50,000 Project Materials
๐Ÿ“ฑ 100% Offline: No internet needed
๐Ÿ“ Over 98 Departments
๐Ÿ” Software coding and Machine construction
๐ŸŽ“ Postgraduate/Undergraduate Research works
๐Ÿ“ฅ Instant Whatsapp/Email Delivery

Blazingprojects App

Related Research

Civil engineering. 3 min read

Optimization of Fly Ashโ€“Geopolymer Concrete for Sustainable Structural Application...

What This Project Is About A practical study of using fly ashโ€“geopolymer concrete to build safer, more sustainable structures that perform well during earthqu...

BP
Blazingprojects
Read more →
Civil engineering. 4 min read

- Assessment of Seismic Retrofit Strategies for Existing Reinforced Concrete Buildin...

What This Project Is About A final-year project exploring how existing reinforced concrete buildings in areas prone to strong earthquakes can be made safer, how...

BP
Blazingprojects
Read more →
Civil engineering. 2 min read

Seismic Retrofit and Performance Evaluation of Low-Cost Housing Using Recycled Polyp...

What This Project Is About A plain-language overview of the topic and what the project investigates. The Problem It Addresses What problem or gap this project ...

BP
Blazingprojects
Read more →
Civil engineering. 3 min read

Life-Cycle Assessment and Optimization of Lightweight Sustainable Concrete for Seism...

What This Project Is About A plain-language overview of the topic and what the project investigates. The Problem It Addresses What problem or gap this project ...

BP
Blazingprojects
Read more →
Civil engineering. 4 min read

Advanced seismic retrofit design of existing reinforced concrete frame buildings usi...

What This Project Is About A straightforward, beginner-friendly overview of upgrading existing concrete frame buildings to perform better during earthquakes. Th...

BP
Blazingprojects
Read more →
Civil engineering. 4 min read

Sustainable Urban Stormwater Management Using Permeable Pavements and Green Roofs: A...

What This Project Is About A plain-language overview of how cities can manage rainwater by using two green infrastructure ideas: permeable pavements, which let ...

BP
Blazingprojects
Read more →
Civil engineering. 2 min read

Optimization of Submerged Floating Tunnel (SFT) Deployment for Offshore Civil Infras...

What This Project Is About A plain-language overview of the topic and what the project investigates. The Problem It Addresses What problem or gap this project ...

BP
Blazingprojects
Read more →
Civil engineering. 4 min read

Seismic Retrofitting of RCC Frame Structures Using Fiber-Reinforced Polymer Wraps an...

What This Project Is About A straightforward study on ways to strengthen concrete buildings (RCC frames) to better withstand earthquakes. It looks at two approa...

BP
Blazingprojects
Read more →
Civil engineering. 4 min read

Integrated sustainable flood-resilient urban drainage system for peri-urban areas: d...

What This Project Is About A plain-language overview of the topic and what the project investigates. The Problem It Addresses What problem or gap this project ...

BP
Blazingprojects
Read more →
WhatsApp Click here to chat with us