<p> <strong>Title page – – – – – – – – i<br>Letter of transmittal – – – – – – ii<br>Approval page – – – – – – – – iii<br>Dedication – – – – – – – – iv<br>Acknowledgement – – – – – – – v<br>Abstract – – – – – – – – – vi<br>Table of contents – – – – – – – vii<br>Nomenclature – – – – – – – – xi<br>

Chapter ONE

: INTRODUCTION<br>1.1 Background of the study – – – – 1<br>1.2 Statement of the problem – – – – 2<br>1.3 Purpose/Aims of the study – – – – 2<br>1.4 Scope and limitation of the study – – – 3<br>1.5 Method of construction of the study – – 5<br>1.6 Significance of the study – – – – – 7<br>

Chapter TWO

: LITERATURE REVIEW<br>2.1 Reactor – – – – – – – – 8<br>2.2 Classification of reactor – – – – – 9<br>2.2.1 Reactor types – – – – – – 9<br>2.2.2 Principle type of reactor – – – – 10<br>2.2.3 Homogenous and hetrogenous reactor – – 10<br>2.2.4 Mode of operation – – – – – – 12<br>2.2.5 Reactor geometry (type) – – – – 13<br>2.3 Fluidised bed reactor – – – – – 14<br>2.3.1 Basic principle of fluidized bed – – – 19<br>2.3.2 Design procedure – – – – – – 20<br>2.3.3 Fluidised bed reactor for mixing gas – – 22<br>2.4 Fluidisation – – – – – – – 24<br>2.5 Mode of operation of fluidised bed reactor – 26<br>2.6 Advantages of fluidized bed reactor – – 28<br>2.7 Disadvantages of fluidised bed reactor – – 29<br>2.8 Uses of fluidized bed reactor. – – – – 32<br>

Chapter THREE

: SELECTION OF MATERIAL<br>3.1 Engineering materials – – – – – 34<br>3.1.1 Classification of engineering material – – 34<br>3.1.2 Metals and alloys – – – – – – 36<br>3.1.3 Ceramic and organic polymer – – – 36<br>3.1.4 Organic materials – – – – – – 36<br>3.1.5 Inorganic materials – – – – – 36<br>3.1.6 Biological materials – – – – – 36<br>3.1.7 Biomaterial – – – – – – – 36<br>3.1.8 Advance material – – – – – – 37<br>3.1.9 General properties of engineering materials – 37<br>3.2 Material selected – – – – – – 43<br>3.21 Factors considered for the selected of material 44<br>3.22 Reason for the material selected – – – 45<br>

Chapter FOUR

: CONSTRUCTIONAL PROCEDURE<br>4.1 Tools and materials used – – – – 47<br>4.2 Steps of fabrication process – – – – 47<br>4.3 Precaution taken during fabrication – – 49<br>

Chapter FIVE

<br>5.0 Discussion – – – – – – – 51<br>5.1 Conclusion – – – – – – – 53<br>5.2 Recommendation – – – – – – 54<br>REFERENCES – – – – – – 56<br>NOMENCLATURE<br> = Pie ca constant with value of 22/7<br>R = Radius of the cylinder/vessels (in inches)<br>H = Height of a cylinder/vessel<br>L = Length of a rectangular plate<br>W = Width of the rectangular plate used<br>R2 = Radiius of the upper and lower nozzle<br>H2 = Height of the upper and lower nozzle<br>L2 = Length of the rectangular of plate used</strong> <br></p>